MeshMatchStudio

Private beta · Mac and Windows

Every color on its own stitch.

MeshMatch Studio measures the canvas taped to your xTool, fits your design to its real threads, and hands xTool Studio a print that lands where it should, even when the canvas is warped.

For the xTool M2 with the inkjet module. You need a beta key: ask for one.

18 mesh mono canvas · one stitch = 1.41 mm

Why we made it

Real canvas is never quite square.

An xTool prints exactly where it's told. The trouble is the canvas. Taped to the bed, it skews and bows, and its threads are never quite where the label says. A design printed straight from xTool Studio starts on its stitches and drifts off them as it goes.

Printed straightOn its stitches at the top left (circled), half a stitch off by the bottom right.
Printed with MeshMatchEvery color follows the threads it belongs to.
  • 17.69

    threads per inch on canvas sold as 18 mesh. Two we measured came in at 17.64 and 17.69.

  • 1 mm

    of drift across three inches when a design is printed straight. One stitch is 1.41 mm.

  • ±0.35 mm

    of room for each color on 18 mesh before it reaches the next stitch.

  • $75+

    for a good blank canvas, so one misprint can cost more than the design.

The old ways

Print the design on paper, lay the canvas over it, nudge and tape. Or print straight and hope, then touch up by hand. Both take time and a steady eye, and neither accounts for a canvas that measures 17.69 instead of 18 or bows toward one corner.

What we wanted

Tape the canvas down, take one set of photos, and have every color land on its own stitch the first time, with no paper to line up and no numbers to type. We built MeshMatch to do that, together with StitchJLM, a needlepoint shop that prints its own canvases on an xTool M2.

How it works

From taped canvas to print

MeshMatch Studio runs beside xTool Studio on your Mac or Windows computer and uses your xTool's own close-up camera, so there's nothing extra to buy. The canvas stays taped in place from the photos to the print.

  1. MeshMatch Studio Setup

    Pick your design

    Drop in a pixel-art PNG. MeshMatch checks it's one color per stitch, removes a solid background, tidies stray shades, and lays out color swatches and your shop logo if you want them.

  2. xTool Studio Canvas Capture

    Tape the canvas and press Close-up stitching

    In xTool Studio, drag the box a little past every edge of the canvas. MeshMatch picks up the photos the moment Studio saves them.

  3. MeshMatch Studio Mesh Analysis, Match

    MeshMatch finds every thread

    Mesh Analysis shows the canvas outline, its size and its real thread count. The Match Engine fits your design to this canvas's own threads, centered by thread count and following any warp.

  4. MeshMatch Studio Match Preview

    See it on your canvas, then check everything

    Match Preview lays the design over the photo of your actual canvas, with a close-up loupe, and lists every check. If one fails, you can't print until it's fixed, and the message says how to fix it.

  5. xTool Studio Print

    Open in xTool Studio and print

    The job opens in xTool Studio already placed, sized and locked, set to ink printing. There are no coordinates to type and nothing to resize. Accept Studio's height measurement and press print.

Once per machine

A five-minute machine test on a blank scrap of canvas measures where your xTool's ink head prints and where each ink color lands. MeshMatch keeps a separate result for each machine, and won't hand you a print from a machine that hasn't had its test.

Features

What MeshMatch takes care of

The checks a canvas painter would make by eye, done for you on the canvas you just taped down.

Fit

Follows the real threads

MeshMatch measures the canvas you taped down, including its real thread count and any skew or bow, and fits the design to it. Stitch 50 lands as close as stitch 1.

Layout

Centered by thread count

The design goes in the middle of the canvas, counted in threads the way a stitcher would count it.

Extras

Swatches and your logo in the corners

One swatch per color, with like colors grouped, and your shop logo, each in the corner you choose, 25 mm from the canvas's real corner. MeshMatch finds that corner even under the finishing tape.

Designs

Cleaned up before printing

If a design was saved on white or as a JPG, MeshMatch removes the background (you can switch this off) and merges near-duplicate shades back into the color you drew.

Hand-off

Opens in xTool Studio, already placed

Right position and size, locked and set to ink printing. In one of our tests, typing the right numbers in by hand still put the print 0.2 to 0.35 mm low. With MeshMatch there's nothing to type.

Checks

Holds back a bad print

Machine set up, canvas blank, whole canvas in the photos, mesh matches the design, design fits, extras clear of the tape, threads found under the design. A failed check stops the print and says how to fix it.

Machine

A setup for each machine

The machine test measures where your xTool prints and where each of eight ink colors lands next to black. Each machine keeps its own result.

Ink

Fills the whole stitch

Ink can land a little short of a stitch's edges. The optional ink fill test lets you draw colors slightly wider to cover it. Where two colors meet, the darker one keeps its edge.

A canvas corner, to scaleThe real edge sits under the finishing tape, several threads past the last clear thread. Swatches and logo are measured from that corner, diagonally.

Results

Measured stitch by stitch

After each test print we photograph the canvas again and measure where the ink landed compared with the threads it was meant for.

0.13 mm

Median distance between a stitch's ink and its thread crossing, across 382 single stitches of a 53 × 53 design on a real canvas. 98% landed within 0.35 mm.

  • Half of all stitches landed inside the small circle
  • 98% inside the large one. The square is one stitch.
Test on an xTool M2Result
Holiday sweater tree, after the machine test, opened directly in xTool Studiored edges centered on their stitches
Reindeer sweater, 53 × 53 stitches with swatches and logo, on "18 mesh" canvas that measured 17.6998% within 0.35 mm
median 0.13 mm
A dot on every crossing across three inchesmedian 0.20 mm
Eight ink colors, each measured against black beside itall within 0.1 mm
Reindeer rows on a canvas lifted at one edgeup to 0.55 mm off

The last row is why MeshMatch asks you to tape every edge. A canvas that lifts off the bed is the biggest source of error left; the M2 itself is accurate to about ±0.2 mm.

These results are from tests on one xTool M2 with 18 mesh mono canvas. That is what is proven so far; other canvas types are in testing. The brochure has the full story and a field guide to printing needlepoint on an xTool.

Who it's for

For makers and shops printing on an xTool M2

Makers

You stitch your own designs and want them printed right the first time, without having to learn the technical side of your printer.

Needlepoint shops

You print canvases to sell. MeshMatch adds your logo and color swatches the same way on every canvas, catches problems before they cost you a canvas, and Print again starts the next copy of a best seller from the last one.

How MeshMatch compares with printing straight from xTool Studio and with paper, align and tape
How it comparesPrint straight from xTool StudioPaper, then align and tapeMeshMatch
Follows a warped or skewed canvasNoBy eyeThread by thread
Uses the canvas's real thread countNoBy eyeMeasured
Design centered by thread countNoBy handAutomatic
Swatches and logo a set distance from the cornerBy handBy handAutomatic
Each machine calibrated, every ink checkedNoNoYes
Stops a bad print before it happensNoNoSeven checks
Numbers to typeX and YX and YNone

Works with

xTool M2 with the inkjet module, xTool Studio (free from xTool), and a Mac or Windows computer.

Tested on

18 mesh mono canvas on the M2 so far. Other canvas types are in testing.

Beta key

Ask for a beta key

MeshMatch is opening to a small group of needlepoint makers and shops with an xTool M2. Write to us and we'll send you a key.

Email us for a beta key

Or write to hello@stitchjlm.com

The button starts an email in your own mail app. Nothing is sent until you press send.

What to tell us

  • Your name
  • Your shop, if you have one
  • Mac or Windows
  • The canvas you use most

We don't need your machine's serial number.

For testers

What you need, and where to start

  • A Mac or Windows computer with xTool Studio
  • An xTool M2 with the inkjet module
  • Blank mono canvas
  • A blank scrap about 4 by 4 inches for the machine test
  • Designs as pixel-art PNGs
  • Your beta key, and an internet connection now and then to check it
  1. Run the machine test first

    In MeshMatch Studio, open Your machine and choose Run the machine test. It takes about five minutes on the blank scrap.

  2. Tape every edge of every canvas

    Flat on the bed with every edge taped matters more than anything else.

  3. Don't move the canvas between capture and print

    It's measured where it lies. If it moves, the measurement no longer matches it.

  4. Test on scrap before a good canvas

    This is a beta. Print on a spare canvas first, and when something looks off, choose Contact in the app and include a photo of the printed canvas.

Questions

Good to know

Does MeshMatch control my xTool?
No. MeshMatch prepares the job and xTool Studio prints it, the same way you print today.
Do I need extra hardware?
No. MeshMatch uses your xTool's own close-up camera through Close-up stitching in xTool Studio.
Can I use my own designs?
Yes. Any pixel-art design with one color per stitch. MeshMatch checks it and cleans up backgrounds and stray shades.
How accurate is it?
On real 18 mesh canvas, 98% of stitches within 0.35 mm and a median of 0.13 mm. Tape every edge flat for results like these.
Is my machine supported?
The xTool M2 with the inkjet module. Tell us what you print on; that decides what comes after.
Does it work without the internet?
Yes, once your beta key is entered. Matching runs on your own computer. MeshMatch Studio checks the key with its server now and then, and asks you to connect if it hasn't been able to for two weeks.

Your photos and designs

MeshMatch Studio matches your design to your canvas on your own computer. Your designs, canvas photos, projects and settings stay there. Your designs stay yours.

The only things sent to MeshMatch's server are your beta key and the serial number of each xTool machine you use it with, to check the key. The waitlist form sends us only the email address you type, to invite you to the beta. This page has no tracking and no cookies.

By using the beta you agree to the short beta terms.